ABB Softstarters
|
Technical data
Type of load |
||||||||||||||||||||||||||||||||||||
Three phase medium voltage AC induction motors | ||||||||||||||||||||||||||||||||||||
AC supply voltage |
||||||||||||||||||||||||||||||||||||
2300, 3300, 4160, 6600/6900, 13,800 VAC +10% to -10% 50/60 Hz line voltages |
||||||||||||||||||||||||||||||||||||
HP ratings * |
||||||||||||||||||||||||||||||||||||
* Consult factory for higher horsepower and voltage requirements. |
||||||||||||||||||||||||||||||||||||
Up to 15,000 HP @ 13,800V (600 Amps max) | ||||||||||||||||||||||||||||||||||||
Overload rating |
||||||||||||||||||||||||||||||||||||
500% – 60 Seconds | ||||||||||||||||||||||||||||||||||||
Power circuit |
||||||||||||||||||||||||||||||||||||
Series strings of SCR (Silicon Controlled Rectifier) power modules (2, 4 or 6 matched pairs of SCRs per phase depending on voltage rating) | ||||||||||||||||||||||||||||||||||||
SCR peak inverse voltage |
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
Transient voltage protection |
||||||||||||||||||||||||||||||||||||
dv/dt circuits (1 per SCR power module) | ||||||||||||||||||||||||||||||||||||
Vacuum bypass contactor * |
||||||||||||||||||||||||||||||||||||
* 13.8 kV, 600A softstarters use circuit breakers for isolation and bypass functions. |
||||||||||||||||||||||||||||||||||||
Standard on all models, line start rated | ||||||||||||||||||||||||||||||||||||
Ambient operating temperature |
||||||||||||||||||||||||||||||||||||
0 to 50°C (32°F to 122°F) (Optional -20° to 50°C with heaters) |
||||||||||||||||||||||||||||||||||||
Control |
||||||||||||||||||||||||||||||||||||
Digital microprocessor controller with read-out in English text Al phanumeric LCD display N on-volatile memory for programming and faults O pto-isolated inputs |
||||||||||||||||||||||||||||||||||||
Communications |
||||||||||||||||||||||||||||||||||||
RS485 with mod bus RTU protocol R S232 with Windows interface |
||||||||||||||||||||||||||||||||||||
Auxiliary contacts |
||||||||||||||||||||||||||||||||||||
FORM C, 8Amps @ 250V | ||||||||||||||||||||||||||||||||||||
Adjustments |
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
Motor and starter protection |
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
Metering |
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
Line start section |
||||||||||||||||||||||||||||||||||||
Load break/fault make disconnect switch with automatic grounding arm and viewing window Fuses with blown fuse indicator In-line vacuum contactor * |
||||||||||||||||||||||||||||||||||||
* 13.8 kV, 600A softstarters use circuit breakers for isolation and bypass functions. |
||||||||||||||||||||||||||||||||||||
Control power transformer with fused primary/secondary Packaged in common enclosure with soft start Optional “Soft Start” (requires customer supplied line start panel) |
||||||||||||||||||||||||||||||||||||
Statistical data |
||||||||||||||||||||||||||||||||||||
Total amount of run time since soft start was reset Amount of time it took motor to start during last period Maximum current during last start period Total number of starts since soft start was reset Event history for last 60 events |
||||||||||||||||||||||||||||||||||||
Elevation |
||||||||||||||||||||||||||||||||||||
1000 m /3300 ft. without derating (contact factory for higher elevations) | ||||||||||||||||||||||||||||||||||||
Enclosure CD * |
||||||||||||||||||||||||||||||||||||
* 13.8 kV softstarters are rated NEMA 1. |
||||||||||||||||||||||||||||||||||||
NEMA 12, top and bottom entrance plates 11 gauge steel ASA #61 gray paint with lifting eyes |