ABB ACS800 AC DRIVES

0.5 to 100Hp @ 208 to 240V
1.5 to 600Hp @ 380 to 500V

• Overview
• Standard Features / Available Options and Software
• Specifications
• Basic Type Code Information
• 230V Ratings (prices)
• 380V Ratings (prices)
• 460V Ratings (prices)
• ACS 800-U2 NEMA 1 R7 & R8 Frame Size and
  ACS 800-02+C111 IP21 (NEMA 1) R7 & R8 Frame Size
• ACS 800 NEMA 1/12 R2 through R6 Frame Size
• ACS 800-02 NEMA 1 R7 & R8 Frame Size
• ACS 800-U4 Module R7 Frame Size
• ACS 800-U4 Module R8 Frame Size

ACS 800 Features

Standard Features

• UL and CUL
• 80 Character Multilingual Alphanumeric Display
• Intelligent Start-Up Assistant
• Adaptive Programming Block with twenty (20) PLC-like functions
• Input Fusing and Fused Disconnect (ACS800-U2 only)
• Three (3) Programmable Analog Inputs (Isolated as a group) (0.025%, 12bit)
• Six (6) Programmable Digital inputs plus one (1) dedicated start interlock
• Two (2) Programmable Analog Outputs (Not Isolated) (0.1 %, 10bit)
• Three (3) Programmable Form C Relay Outputs
• Run Enable
• Adjustable Filters on Analog Inputs and Outputs
• Input Speed Signals
  • Two (2) Current 0 (4) – 20 mA
  • One (1) Voltage +/- 0 (2)- 10VDC
  • Increase/Decrease reference Contacts
• Start/Stop
  • 2 Wire (Dry Contact Closure)
  • 3 Wire (Momentary Dry Contacts)
• Adjustable Current Limit
• Adjustable Torque Limit
• Nine (9) Supervision Functions
• Electronic Reverse
• Motor ID Run
• Power Loss Ride-Through
• DC Magnetizing Start (provides maximum starting torque)
• DC Hold
• Flux Braking
• Flux Optimization
• Fifteen (15) Preset Speeds
• Three (3) Critical Speed Lockout Bands
• Self-Tuning Speed Controller
• Direct Torque Control (DTC^TM)
• Scalar Control
• Automatic Reset Customer Selectable
• Two (2) Independently Adjustable Accel and Decel Ramps
• Linear or Adjustable “S” Curve Accel/Decel Ramps
• Ramp or Coast to a Stop
• Maximum Frequency Programmable up to 300 Hz (scalar and DTC mode)
• Integral Programmable PID Setpoint Controller
• Mathematical Functions on Analog Reference Signals
• AC (R4 Frames & above) or DC (R2 & R3 Frames) Reactor
• Integral Brake Chopper (R2 & R3 Frames)
• Reference Trim
• Brake Control
• Master/Follower
• Programmable Fault Functions for Protection:
  • AI<Min
  • Panel Loss
  • External Fault
  • Motor Thermal Protection
  • Stall
  • Underload
  • Motor Phase Loss
  • Ground Fault
  • Communications Fault
• Preprogrammed Protections:
  • Overcurrent
  • Short Circuit
  • Overvoltage (Intermediate Circuit)
  • Undervoltage (Intermediate Circuit)
  • Input Phase Loss
  • Output Device and Control Board Overtemperature

Available Options

• DDCS Communications Card RDCO-01/-02/-03
• Analog I/O Extension Card RA10-01
• Digital I/O Extension Card RD10-01
• Pulse Encoder Interface RTAC-01
• Fieldbus Adapter Modules
  • DeviceNet RDNA-01
  • Profibus-DP RPBA-01
  • Modbus Adapter RMBA-01
  • Interbus-S RIBA-01 (not available at time of printing)
  • Modbus Plus RMBP-01 (not available at time of printing)
  • Control Net RCNA-01 (not available at time of printing)
  • Ethernet RETA-01 (not available at time of printing)
• Dynamic Braking Choppers (R4 through R8 Frames)
• CE EMC Filters (1st and 2nd Environments)
• DriveWindow@-based Adaptive Programming Tool
• DriveWindow@-based Start-up and Programming Tool

Application Software

• Pump/Fan Control
• Extruder
• Spinning
• Traverse
• Centrifuge / Decanter

© 2004 ABB Inc. All rights reserved Specification and pricing subject to change without notice.

ACS800-US-03 Rev. B

Effective: 06/11/03 Supersedes: 10/07/02